使用要求
組成部分：本機主要由機架部分、壓榨部分、驅動部分、加熱部分等組成，鑒于環保及循環利用意識，進料/收料裝置可用飲料瓶等代替，故于用戶自備。
組 裝：使用前應將機架進行固定，固定時確保手柄能自由轉動，之后將減摩墊圈浸上少許植物油套在榨螺小端，裝入機架的榨膛中，與手柄連接并用螺栓固定，再將接頭旋緊到榨膛上，調節螺塞擰入接頭上.
燃料瓶中注入80%左右的燃料（煤油或酒精），將約15cm燈芯穿入擋片中，露出約0.5cm，之后將燈芯長端放入燃料瓶中，擋片放置瓶口，將燃料瓶置于機架集熱罩下端，并用橡皮筋固定。
加 熱：為保證出油效果，一般在榨制前需對榨膛進行預熱約10分鐘，榨膛溫度到50－70℃后再在進料口加入原料進行榨制。榨油過程中需要持續加熱。
操 作：確保壓榨前原料中沒有雜質異物.
壓榨開始，少量油從調節螺塞處流出屬于正常現象。
如果油餅過干或者手柄轉動阻力過大,放松調節螺塞。
如果油餅中油殘留過大，加緊調節螺塞。
清 理：使用后應及時清理，否則機器內殘留物硬化影響下次的正常使用。
安全警示：由于物料的自摩擦產生的熱能及燃料瓶的加熱，造成機架榨膛及接頭、調節螺栓溫度較高，應避免與高溫部分接觸，如的確需操作高溫部件請采取合理的防護措施。
聲 明：隨著技術進步，公司產品在不斷更新。恕不另行通知產品變化。
Operation requirement:
Components: This machine consists of frame, press part, driver part and heating part etc. In view of environmental protection and recycling, material feeding/collecting equipment can be replaced with drink bottle, which is prepared by buyer.
Assembly：Before operation please fix the frame and make sure crank can be turned freely.
Lubricate washer with edible oil and insert on screw shaft from the small end.
Insert screw shaft in press cage.
Screw on press cage cap and screw on terminal adjustment bolt.
Attach crank arm to screw shaft and tighten the bolt.
Fill 80% fuel to the lamp bottle (kerosene or alcohol). Pass a 15cm wick through the washer. Leave 0.5cm of wick outside and put the longer end in the fuel bottle. Place washer at the bottle mouth. Place the lamp under press cage. Secure the lamp with rubber band.
Heating: To guarantee the oil output, the press cage should be heated for about 10 minutes. when the press cage temperature reaches 50－70℃, material can be put into inlet for pressing. The lamp remains heating during pressing as well.
Operation: Make sure no impurities in the material before pressing.
At the beginning of pressing, oil flowing from the terminal adjustment bolt is normal.
Loose the terminal adjustment bolt if the discharged cake is too dry and crank turning resistance is too big
Tighten the terminal adjustment bolt if the discharged cake contains too much oil residual.
Cleaning: Clean the oil press immediately after operation. Otherwise residual in the machine will get hard and affect next operation.
Safety and warnings
Material friction and lamp heating cause very hot press cage, press cage cap and terminal adjustment bolt. Keep hands clear of the hot parts. And if you indeed need operate the hot parts please take reasonable protection steps.
Notes: With technology renewal our product is improved continuously. We are not liable for informing buyer about product change in future.
配件名稱：
- 手柄 crank
- 燃料瓶 fuel bottle
- 機架 frame
- 榨螺 screw shaft
- 榨膛press cage
- 接頭 press cage cap
- 調節螺塞 terminal adjustment bolt
更多的操作細節，請關注我們的專業視頻。
http://www.creamoweber.com/shipin/